Specification :

Detail:

DC brushless motor controller Features
# SPWM, Speed/ Current alike close loop technology, smooth rotation
# Smooth torque output within speed range ( 8000 rpm Max.)
# 1: 75 Max. speed regulation ratio
# 60/ 300/ 120/ 240Electrical angle adjustable
# Speed regulation: potentiometer adjust / Analog input
# Run/ Step, Quick Brake, CW/ CCW rotation shift
# Speed output, Alarm output( O.C.)
# Over current, over voltage, stall, missing speed Alarm

Parameters
Electrical Parameters( Tj25C)

- - - -
Power | 2450VDC, Capacity: uptomotors |
Currentoutput | Rated15A, Peak45A( 3s) |
Drivingmode | SPWM |
InsulationRes. | 500M |
DielectricStrength | 500V/ Minute |
Weight | About300g |
- - - -

Ambientrequirement

- - - -
Cooling | Selfcool |
Environment | Keepawayfromoil, dust, andacidgas |
Temperature | 0C50C |
Humidity | 80RH |
Vibration | 5.7m/ s2.Max. |
Storagetemp. | 20C125C |
- - - -

Function description
# Power Supply: DC+ ; DC-

Voltage: 2450DC, normally Linear Power Supply applied( appendix) , ripple voltage higher than 50V may damage driver. The output current of LPS shall be 60more than that of driver. In case of switching power supply( strongly recommended) applied, please pay attention to the current shall meet motors current.
Attention: incorrect connection may cause driver damaged.
# Speed regulation choice( RV ; AVI)

1.Setup speed by potentiometer ( RV) .The dipswitch SW2 must be ON status to enable this function. CW rotate the potentiometer will increase speed. CCW- speed down.

2.Setup speed by analog input ( AVI) . The dipswitch SW2 must be OFF status to enable this function..AVI terminal accept 05V voltage or PWM signal from controller.AVI terminal with input resistance of 100K, current consumption5mA.

Referencetable

- - - -
SW2 | Commandto | Speedadjust | Comman | Current |
ON | RV | CWspeedup, CCWspeeddown | | |
OFF | AVI | 05Vanaloginput | 05Vvolage | 5mA |
OFF | AVI | PWM | 1KHzdutycycle | |
- - - -

Only one of above two modes can be used to adjust speed ( another mode shall be enabled) . Once AVI terminal applied, ( RV) potentiometer shall be CCW turned to Min. position.PWM signal are 5V TTL level.

# Run/ Stop( ENBL)

ENBL terminal is applied to control motor Run/ Stop, Common positive terminal is 5V.

Optical coupler short circuit make motor run, it open circuit make motor stop.

See below circuit

# CW/ CCW Rotation( F/ R)

F/ R terminal is applied to shift motor rotate direction, common positive terminal is5V.

Motor run in CCW when optical coupler is short circuit, motor run in CW when optical coupler is open circuit.

Attention: dont change the connection sequence of phase wires of motor to shift rotate direction.
# Motor Brake Command( BRK)

BRK terminal applied to stop rotation quickly. Motor will stop normally within 50ms. But inertia of load cant exceed 2 times of motor inertia, otherwise brake will cause driver alarm.

Time of acceleration and deceleration must be put into controller in case of too big load inertia,

And please dont use brake function in such condition.

The optical coupler short circuit will brake motor, optical coupler open circuit release motor to run.
# Setup different electrical angle

Dipswitch SW1 can be setup to fit motors with different electrical angel

- - - -
SW1 | |
ON | 120or240hallsignal, theyareinoppositerotationdirection |
OFF | 60or300hallsignal, theyareinoppositerotationdirection |
- - - -

# Motor rotation speed output( SPEED)

Pulse generated by driver are proportioned with motor speed, ( isolated O.C. output) it can be increased to be a random level. 6 multiple frequency processed output.

Motor speed60SPEED( pulse freq.) / pulses per rev. of motorp.p.rmotor pole pairs6
# Alarm output( ALM)

Driver will enter protection mode and stop motor running in case of OVER CURRENT, OVER VOLTAGE, SHORT CIUCUIT, MOTOR STALL arise, LED on driver will be light, and ALM signal will be available. Please cut off drivers power supply, check wiring and voltage. High voltage is not permitted for big inertia motor, as it may cause run/ stop frequently and over voltage alarm. Circuit of this function refer to pic. 2.

# Terminals description

- - - -
Terminalmark | Description |
DC+ DC- | Voltagesupplytodriver |
UVW | Tomotorleads.Makesurecorrectconnectiontomotorleads. |
REF+ REF-HUHVHW | Hallsensorconnection, REF+
REF-areforhallpowersupply.Makesurecorrectconnectiontohalls. |
AVIENBLF/ RBRKVcc | Controlsinput, seebelowpicture |
SPEEDALM | Signaloutput, ( O.C.) |
- - - -

# Wiring Diagram

Dimension
Model Number: BLDC-5015A
Brand Name:
Payment Terms:
Minimum:
Certification:
Delivery Time:
Supply Ablity: