Portable Industrial Combustion & Emission Analysers
Greenline 6000 and Greenline 8000
- Up to 9 Sensors
( Temperature Compensated)
- Remote Control Unit
with Built In Printer
- Full Compliance to
EPA Protocols
- CO, CO2 and Cx Hy
- Built In NDIR Sensors
Built In Peltier Gas Cooler and
Industrial Heated Probe
- CO Sensor Automatic
Protection with Purge Pump
- Long Term Monitoring
with Automatic Water
Condensation Drain
- Electronic Flow Meter
- Aux 4 20mA Inputs
- Graphic Display with Menu
- Easy Maintenance
- 9000 Full Analysis Memory,
TM USB, & Windows Software

Introduction
Gas Analysis Main Control Unit ( MCU) and Remote Control Unit ( RCU) .
Hand Held Remote Control Unit with Reporting Printout Capability, Test
Memory and PC Communication.
Measurement capability for O2 , CO, CO2 , NO, NO2 , SO2 , Cx Hy with
Electrochemical Sensors.
Full Compliance to EPA ( Environmental Protection Agency) Protocols
CTM 030 and CTM 034.
The Most Advanced Portable Emissions Analyzers with Stack Velocity
Measurement.
GreenLine 8000 only:
Optional Industrial Sampling Probe Including Heated Probe Head and
Heated Hose.
Built In Peltier Gas Cooler and Automatic Water Condensation Drain.
Direct Measurements of CO, CO2 , Cx Hy with Internal NDIR Sensors.

SENSOR TECHNOLOGY
AOIP flue gas analyzers use long life
temperature compensated EC
( electrochemical) sensors.
NDIR SENSOR
CO sensor is protected against
saturation by an electrovalve and clean
air purge pump.
Only GreenLine 8000 uses a
nondispersive Infrared ( NDIR) dual
wavelength ratioing to get long term
stable response sensitivity.
Compensation of ambient temperature
and pressure is automatic.
EASY ACCESS SENSORS AND FILTERS
These analysers are easy to maintain. A
quick access compartment allows the
operator to easily view and change ALL
of the sensors, filters, and pneumatic
parts. The user is able to effortlessly
change the unit’ s sensors or filters in
the field if necessary.
CALIBRATION
A built in procedure allows easy and
automatic span sensor calibration using
a standard gas cylinder. Periodic zero
calibration doesn' t require to remove
the probe from stack; an internal
electrovalve switch to an auxiliary
pneumatic circuit for fresh air. A
pneumatic connector for remote zero
air is also available.
ELECTRONIC FLOW METER
An automatic built in system measures
a flow of sampling gas and adjusts the
pump to obtain a constant sampling
volume. A visual and acoustic alarm
indicates a low rate.
MULTI FUEL SELECTION
The flue gas analysers provide up to 10
fuels for calculating combustion values.

Most used fuels for your country are
pre loaded from factory. Others fuels
can be added using the GasConfig PC
software.
GAS PROBE & SAMPLING SYSTEM
Flue gas sampling probes with different
lengths, shapes and max. operating
temperatures ( 1500° F and 1800° F) are
available to match the various
requirements of different applications.
A sintered pre filter is suggested for
severe and heavy applications. The
built in water trap drains condensation
moisture periodically from the system
with a peristatic pump. A dual filtering
system ( quartz + line) will clean the gas
sample before the analysis.
INDUSTRIAL PROBE & HEATED HOSE
For GreenLine 8000 only, a heated
sampling probe is available for
industrial high temperature
applications. A heated hose allows flue
gas sampling without condensation.
The internal cooler dries the flue gas
and avoids dilution of NO2 and SO2 into
the condensate.
SEMI CONTINUOUS MONITORING
The industrial design and the advanced
technology of the unit, allow it to
perform long term gas analysis on a
long time basis. The procedure acquires
and logs the data after a programmable
period of time. A “ smart� procedure
allows the unit to maximize the sensor
life by switching the pump off, during
the sleep phase.
KEYBOARD & DISPLAY
The RCU Keypad allows the operator to
enter all operative modes following
easy menu driven instructions.

The high contrast graphic LCD ( 44 x 62
mm) is equipped with an automatic
backlight device.
It displays the measured and calculated
parameters in your preferred format
( Zoom function 3, 6 or 12 lines) .
Parameters can be also displayed in a
bar graph mode.
BUILT IN IMPACT PRINTER
The RCU is equipped with a built in,
rugged impact printer. It uses a low cost
common roll of paper ( 58 mm large, 18
meters long) .
Definitely more readable, and heat
resistant overtime than the thermal
printout on chemical paper.
PRESSURE & DRAFT
The instrument is equipped with an
internal differential sensor to measure
pressure and stack draft. Differential
pressure could be
used, e.g., for stack gas velocity
measurement by using an optional Pitot
tube.
AUXILIARY INPUTS
Two scalable 4 20mA are available to
measure and store process parameters.
AMBIENT CO PROBE
An optional probe is available to
monitor ambient CO concentration to
keep the operator in a safe
environment. The instrument gives
acoustic
and visual alarms if the set limits
( according to the OSHA
recommendation) are exceeded.

Parameter sensor Range Resol. Accuracy
O2 Electrochemical 0  25% 0.1% ± 0.1% vol
CO
H2